Steel Angle and Channel Size Chart

AISC weights, areas and dimensions for common steel angles, C channels and MC channels, with how to read and weigh each shape.

Updated October 2026 4 min read By the ASA team

On this page
  1. Equal leg angle size chart
  2. Unequal leg angle size chart
  3. Channel size chart: C and MC shapes
  4. Reading designations and calculating weight
  5. Grades and tolerances
  6. Angle and channel from ASA

This steel angle and channel size chart lists published AISC values for common structural angles, American Standard channels (C) and miscellaneous channels (MC). Angles are named by leg lengths and thickness, so an L4 x 4 x 1/2 has two 4 in legs, is 1/2 in thick and weighs 12.8 lb per foot. Channels are named like beams, by nominal depth and weight per foot: a C8x11.5 is 8 in deep and weighs 11.5 lb per foot.

Weights, areas and dimensions are the decimal values from the AISC Shapes Database, consistent with the 16th Edition of the AISC Steel Construction Manual. For section properties used in design, refer to the Manual.

Equal leg angle size chart

Angle (in)Thickness (in)Weight (lb/ft)Area (sq in)
L2 x 2 x 1/80.1251.650.491
L2 x 2 x 3/160.18752.440.722
L2 x 2 x 1/40.2503.190.944
L2 x 2 x 3/80.3754.701.37
L2-1/2 x 2-1/2 x 3/160.18753.070.901
L2-1/2 x 2-1/2 x 1/40.2504.101.19
L2-1/2 x 2-1/2 x 3/80.3755.901.73
L3 x 3 x 3/160.18753.711.09
L3 x 3 x 1/40.2504.901.44
L3 x 3 x 3/80.3757.202.11
L3 x 3 x 1/20.5009.402.76
L3-1/2 x 3-1/2 x 1/40.2505.801.70
L3-1/2 x 3-1/2 x 3/80.3758.502.50
L4 x 4 x 1/40.2506.601.93
L4 x 4 x 5/160.31258.202.40
L4 x 4 x 3/80.3759.802.86
L4 x 4 x 1/20.50012.83.75
L4 x 4 x 3/40.75018.55.44
L5 x 5 x 5/160.312510.33.07
L5 x 5 x 3/80.37512.33.65
L5 x 5 x 1/20.50016.24.79
L6 x 6 x 3/80.37514.94.38
L6 x 6 x 1/20.50019.65.77
L6 x 6 x 3/40.75028.78.46
L6 x 6 x 11.00037.411.0
L8 x 8 x 1/20.50026.47.84
L8 x 8 x 3/40.75038.911.5
L8 x 8 x 11.00051.015.1

Angles with legs under 3 in are often called bar size angles. They are specified and ordered the same way as larger structural angles: legs, then thickness, then grade and length.

Unequal leg angle size chart

Unequal leg angles are written long leg first. Specify which leg is outstanding or connected on the drawing, since the two legs have different section properties and hole gages.

Angle (in)Thickness (in)Weight (lb/ft)Area (sq in)
L3 x 2 x 1/40.2504.101.20
L3 x 2 x 3/80.3755.901.75
L3-1/2 x 2-1/2 x 1/40.2504.901.45
L4 x 3 x 1/40.2505.801.69
L4 x 3 x 3/80.3758.502.49
L4 x 3 x 1/20.50011.13.25
L5 x 3 x 1/40.2506.601.94
L5 x 3 x 3/80.3759.802.86
L5 x 3-1/2 x 3/80.37510.43.05
L5 x 3-1/2 x 1/20.50013.64.00
L6 x 4 x 3/80.37512.33.61
L6 x 4 x 1/20.50016.24.75
L7 x 4 x 1/20.50017.95.26
L8 x 4 x 1/20.50019.65.80
L8 x 6 x 1/20.50023.06.80

Channel size chart: C and MC shapes

Channels have a web and two flanges on one side. The inside faces of the flanges are sloped, so AISC lists an average flange thickness. American Standard channels (C) have a standard flange slope; miscellaneous channels (MC) cover depths and flange widths outside the C series, including much wider flanges for a given depth and some very light sections.

American Standard channels (C shapes)

Channel (lb/ft)Depth d (in)Flange width bf (in)Web tw (in)Flange tf, avg (in)
C3x4.13.001.410.1700.273
C3x53.001.500.2580.273
C3x63.001.600.3560.273
C4x5.44.001.580.1840.296
C4x7.254.001.720.3210.296
C5x6.75.001.750.1900.320
C5x95.001.890.3250.320
C6x8.26.001.920.2000.343
C6x10.56.002.030.3140.343
C6x136.002.160.4370.343
C7x9.87.002.090.2100.366
C7x12.257.002.190.3140.366
C8x11.58.002.260.2200.390
C8x13.758.002.340.3030.390
C8x18.758.002.530.4870.390
C9x13.49.002.430.2330.413
C9x159.002.490.2850.413
C10x15.310.002.600.2400.436
C10x2010.002.740.3790.436
C10x2510.002.890.5260.436
C10x3010.003.030.6730.436
C12x20.712.002.940.2820.501
C12x2512.003.050.3870.501
C12x3012.003.170.5100.501
C15x33.915.003.400.4000.650
C15x4015.003.520.5200.650
C15x5015.003.720.7160.650

Miscellaneous channels (MC shapes)

Channel (lb/ft)Depth d (in)Flange width bf (in)Web tw (in)Flange tf, avg (in)
MC6x126.002.500.3100.375
MC6x186.003.500.3790.475
MC8x8.58.001.870.1790.311
MC8x208.003.030.4000.500
MC8x22.88.003.500.4270.525
MC10x8.410.001.500.1700.280
MC10x2210.003.320.2900.575
MC10x2510.003.410.3800.575
MC12x10.612.001.500.1900.309
MC12x3112.003.670.3700.700

Tip: Unlike wide flange beams, C shapes in a series all share the same nominal depth exactly: every C10 is 10.00 in deep, and the extra weight goes into a thicker web and slightly wider flanges. A heavier channel keeps the same depth and flange thickness, but check bolt grip and clearances for the thicker web.

Reading designations and calculating weight

  • Angle: L, long leg, short leg, thickness, for example L6 x 4 x 3/8. Both legs have the same thickness.
  • Channel: C or MC, nominal depth, weight per foot, for example C10x15.3 or MC12x31.
  • Length: total weight is lb/ft times length in feet. A 20 ft L3 x 3 x 1/4 weighs about 4.9 x 20 = 98 lb.

For an angle, weight per foot can be checked from its geometry: area is roughly thickness x (leg A + leg B − thickness), and steel weighs about 3.4 lb per foot for each square inch of area. For an L4 x 4 x 1/2 that gives 0.5 x 7.5 x 3.4 = 12.75 lb/ft, against 12.8 lb/ft in the AISC table. The small difference comes from the root fillet and rounded toes.

For gussets, clip plates and base plates that go with angle and channel framing, the steel plate weight calculator gives plate weights by size. Beams are covered in the wide flange beam size and weight chart.

Grades and tolerances

Structural angles and channels are most commonly produced to ASTM A36, with 36 ksi (250 MPa) minimum yield and 58 to 80 ksi (400 to 550 MPa) tensile strength, and also to higher strength grades such as A572 Grade 50. Weathering grades such as A588 are available for exposed structures. Dimensional tolerances for rolled shapes, including leg length, thickness, out-of-square and straightness, are set by ASTM A6. Actual dimensions vary within those tolerances, so measure critical fit-ups.

Angle and channel from ASA

American Steel & Aluminum supplies angle, channel and wide flange beam in A36, A992, A709 and A588 as part of its structural shapes line. ASA’s structural processing includes angle punching, clip angles, sawing and miter cutting up to 25 in square with bevels to 45 degrees, and drilling and coping, with delivery across New England and New York on company-owned trucks.

Frequently asked questions

How do you read a steel angle size?

An angle size lists the two leg lengths and then the thickness, all in inches. L6 x 4 x 3/8 has a 6 in leg, a 4 in leg and a 3/8 in thickness. Unequal angles are written long leg first. Weight is not part of the name, so look it up in the AISC table: an L6 x 4 x 3/8 weighs 12.3 lb per foot.

What is the difference between C and MC channels?

C shapes are American Standard channels, a standardized series in which every section has the same inner flange slope. MC shapes are miscellaneous channels that fill gaps around that series, with wider flanges for a given depth or lighter sections. Both are listed in the AISC Manual, and the letter must be on the order because the shapes are not interchangeable.

How much does a 20 foot steel angle weigh?

Multiply the AISC weight per foot by 20. A 20 ft L2 x 2 x 1/4 weighs about 64 lb, an L3 x 3 x 1/4 about 98 lb and an L4 x 4 x 1/2 about 256 lb. These are theoretical weights; actual pieces vary slightly within rolling tolerances, and cut lengths include saw kerf.

What does C8x11.5 mean?

C8x11.5 is an American Standard channel 8 in deep that weighs 11.5 lb per foot. Its AISC dimensions are a 2.26 in flange width, a 0.220 in web and a 0.390 in average flange thickness. Heavier C8 channels, such as C8x13.75 and C8x18.75, keep the 8 in depth and add web thickness and flange width.

Material, processing and fabrication from one supplier

Send a drawing or a material list and the ASA team will quote it from stock.