G60 Galvanized Steel: Coating Weight, Specs and Uses

G60 is the mid-weight zinc coating behind most steel framing, ductwork and indoor equipment. Here is what the designation guarantees and where it stops being enough.

Updated October 2026 5 min read By the ASA team

On this page
  1. G60 coating requirements
  2. Why G60 is the framing and duct baseline
  3. G60 vs G40 vs G90: choosing by exposure
  4. Working with G60 in the shop
  5. Specifying G60 on drawings and orders
  6. G60 galvanized steel from ASA

G60 galvanized steel is ASTM A653 hot-dip galvanized sheet carrying at least 0.60 oz/ft² of zinc, total on both sides, by the triple spot test. That is about 0.51 mil (13 µm) of zinc per side, enough for interior and sheltered service with real moisture exposure, such as framing inside wall cavities, ductwork and equipment housings.

G60 is the workhorse middle coating. It carries 50% more zinc than G40 and two thirds of the zinc on G90, and for many building and equipment applications it is the minimum that codes and industry standards accept.

G60 coating requirements

ASTM A653 expresses the G designation in hundredths of an ounce per square foot, both sides combined. For G60, the standard sets these minimums:

TestRequirementApprox metric
Triple spot, total both sides0.60 oz/ft² minAbout 183 g/m²
Triple spot, one side0.20 oz/ft² minAbout 61 g/m²
Single spot, total both sides0.50 oz/ft² minAbout 153 g/m²

Metric values in the table are direct unit conversions. Under the metric edition of the standard, the nearest designation is Z180, which has its own rounded test limits, so use one system consistently on a drawing and purchase order.

On thickness: 1 oz/ft² of zinc is about 1.7 mils (43 µm). The 0.60 oz/ft² total is roughly 1.02 mils (26 µm), split between the two faces. The zinc is part of the stated gauge thickness, not added to it.

Why G60 is the framing and duct baseline

Several industry standards treat G60 as the minimum zinc for components that live inside buildings but can still get wet.

Cold-formed steel framing

Structural studs, joists, track and headers are typically required to carry at least a G60 coating under the cold-formed steel framing standards (ASTM C955 and the AISI framing standards it works with). Framing inside a wall or floor assembly may see condensation, construction moisture or a roof leak, and its strength depends on the steel thickness that remains. Many specifications step up to G90 for exterior walls, coastal sites and other humid exposures.

HVAC ductwork

Galvanized duct built to SMACNA construction standards is commonly specified as G60 for general supply and return systems in conditioned buildings. Duct running outdoors, through unconditioned spaces, or carrying humid exhaust is often upgraded to G90 or to another material. Always check the mechanical specification, which governs over any general rule.

Other common G60 uses

  • Electrical boxes, raceway components and interior enclosures
  • Garage door panels and interior door components
  • Appliance cabinets and housings before painting
  • Interior data center hardware such as brackets, blanking panels and containment parts
  • Storage racks and shelving in warehouses without washdown

G60 vs G40 vs G90: choosing by exposure

The right coating weight follows from how much moisture the part will see and how long it has to last. A practical way to decide:

ExposureTypical choiceWhy
Dry, conditioned interiorG40 or G60Zinc consumption is very slow
Inside walls, ceilings, duct systemsG60Occasional condensation and construction moisture
Unconditioned spaces, humid plantsG90Frequent wetting shortens coating life
Outdoor, washdown, coastalG90 or heavier, often paintedRain, salt and chemicals consume zinc faster

Coating life is close to proportional to zinc weight in a given environment, so G90 should outlast G60 by roughly 50% under the same conditions. The price step from G60 to G90 is usually modest. When a part is borderline, the cheaper insurance is almost always the heavier coating, not a later repair. For the next step up, see G90 galvanized steel; for the lighter option, see G40 galvanized steel.

Tip: If a part will be powder coated and installed indoors, G60 under the powder often gives better value than G90 bare. If it will go outdoors, G90 under the powder is the safer combination.

Working with G60 in the shop

G60 handles normal sheet metal work without special treatment. A few points help parts come out clean:

  • Forming: the coating is ductile and stays adherent through press brake bends and roll forming. Use Forming Steel (FS) rather than Commercial Steel (CS) for tight hems and severe roll forming, and Deep Drawing Steel (DDS) for deep draws.
  • Cutting: fiber laser, punch and shear all leave cut edges that the surrounding zinc protects for a time. Edges on thin G60 in interior service rarely need touch up.
  • Spot welding: zinc alloys with copper electrodes and shortens their life, so welders run higher current and dress tips more often than on bare steel. G60 is easier on electrodes than G90.
  • Arc welding: zinc vaporizes ahead of the arc, so remove coating at the joint where practical, use fume extraction, and repair the area afterward with zinc rich paint.
  • Storage: keep bundles dry and ventilated. Water trapped between sheets causes white rust within days.

Painting over G60

Galvanized sheet must be cleaned and pretreated before paint or powder, and mill passivation can interfere with adhesion. Tell the supplier when the sheet will be coated so the right surface treatment is ordered. A paint or powder layer over G60 is a duplex system, which outlasts either the zinc or the paint alone because each protects the other.

If every part in the job will be painted and spot welded, compare G60 with A60 galvannealed before ordering. A60 carries the same 0.60 oz/ft² total, but the zinc is alloyed with iron into a matte surface that takes paint with less preparation and welds with longer electrode life. Left bare, though, G60 is usually the better choice: galvannealed sheet is designed to be painted, and its matte gray surface is less attractive and less forgiving of scratches without a finish over it.

Specifying G60 on drawings and orders

An incomplete callout is the most common cause of the wrong material showing up. Include:

  1. Specification: ASTM A653
  2. Designation: CS Type B for general use, FS for severe forming, or SS with a grade (for example SS Grade 33) for load bearing members
  3. Coating: G60
  4. Surface: passivated or unpassivated, oiled or dry, regular or minimized spangle
  5. Thickness: in decimal inches, with gauge for reference

For framing, the member thickness is usually called out as a minimum base metal thickness in mils, which excludes the coating, so confirm which convention the drawing uses. A full background on coatings and test methods is in the guide to what galvanized steel is.

G60 galvanized steel from ASA

ASA stocks ASTM A653 galvanized sheet, mainly in G90, in its flat-rolled sheet and plate line, with mill certifications and full material traceability available. Ask about G60 availability when you request a quote. ASA levels and cuts coated steel from 24 to 11 gauge to length, then laser cuts, press brake forms, welds and powder coats parts in house. For repeat production, kanban and vendor managed inventory programs keep G60 parts on hand, with most JIT orders delivered in 24 to 48 hours.

Frequently asked questions

Is G60 galvanized steel rated for exterior use?

G60 can be used outside in dry inland climates or under a paint system, but it is not the usual choice for bare exterior sheet metal. Rain, dew and pollutants consume zinc faster than indoor air, and 0.51 mil per side leaves limited reserve. Most specifications call for G90 or heavier on exposed exterior parts, especially near salt water.

What is the metric equivalent of G60?

The closest metric designation is Z180, meaning about 180 grams of zinc per square meter total on both sides. A direct conversion of 0.60 oz/ft² gives about 183 g/m², so the two are nearly equal but not identical. Because test limits are rounded differently in each system, a drawing should name one designation and the matching standard.

Does G60 mean 0.60 oz of zinc on each side?

No. The 0.60 oz/ft² figure is the minimum for both sides added together, averaged over three samples. Each side carries roughly half, about 0.30 oz/ft² or 0.51 mil, and A653 requires at least 0.20 oz/ft² on any one side. Misreading the total as a per side value is a common error when comparing quotes.

Why do steel stud standards require G60?

Steel framing is thin, often under 0.100 in, and its load capacity depends on how much steel remains over the life of the building. Wall and floor cavities can trap condensation and construction moisture for long periods. A G60 minimum gives enough zinc to protect the base steel through those wetting cycles, and many projects specify G90 in harsher locations.

Can G60 galvanized steel be laser cut?

Yes. Fiber lasers cut G60 cleanly, and the zinc burns back only a short distance from the edge. The surrounding coating protects that narrow bare edge galvanically for a time, which is usually sufficient indoors. Expect a small amount of zinc residue on the dross side, and use nitrogen or air assist when edges will be painted or welded afterward.

Material, processing and fabrication from one supplier

Send a drawing or a material list and the ASA team will quote it from stock.