On this page
In the 304 vs 316 stainless steel decision, the key difference is molybdenum: 316 contains 2 to 3% molybdenum and more nickel, which gives it much better resistance to chlorides such as salt water, deicing salt and chlorinated chemicals. 304 costs less and is enough for most indoor, freshwater and food applications; choose 316 for coastal, marine and chemical exposure.
Otherwise the two grades are close relatives. Both are austenitic, both are nonmagnetic when annealed, and ASTM A240 sets the same minimum strength for each. They cut, form and weld in nearly the same way, so the choice rests on environment and budget.
304 vs 316 side by side
| Property | 304 | 316 |
|---|---|---|
| UNS number | S30400 | S31600 |
| Chromium | 17.5 to 19.5% | 16.0 to 18.0% |
| Nickel | 8.0 to 10.5% | 10.0 to 14.0% |
| Molybdenum | Not specified | 2.00 to 3.00% |
| Carbon, max | 0.07% | 0.08% |
| Tensile strength, min | 75 ksi (515 MPa) | 75 ksi (515 MPa) |
| Yield strength, min | 30 ksi (205 MPa) | 30 ksi (205 MPa) |
| Elongation in 2 in, min | 40% | 40% |
| Hardness, max | 92 HRB (201 HBW) | 95 HRB (217 HBW) |
| Density, typical | 0.289 lb/in³ (8.00 g/cm³) | 0.289 lb/in³ (8.00 g/cm³) |
| Thermal expansion, typical (32 to 212°F) | 9.6 µin/in·°F (17.3 µm/m·°C) | 8.9 µin/in·°F (16.0 µm/m·°C) |
| PREN, typical | About 18 to 20 | About 23 to 25 |
| Magnetic when annealed | No | No |
| Relative material cost | Lower | Higher |
Composition and mechanical values are ASTM A240 limits for annealed sheet, strip and plate; physical values and PREN are typical. The low-carbon versions, 304L and 316L, follow the same pattern with 0.030% maximum carbon and minimum strengths 5 ksi lower, unless the material is dual certified.
Corrosion resistance: where the difference shows
In clean air, fresh water, steam, most foods and many mild chemicals, 304 and 316 perform about the same. Paying for 316 in those conditions buys little. The gap opens when chlorides are present, and it widens as chloride concentration, temperature and the number of crevices rise.
Chlorides and pitting
Chloride ions break through the passive film at small weak spots and start pits that can grow deep while the surrounding surface looks fine. The molybdenum in 316 makes the film more stable and quicker to repair, so pits are harder to start. A common rule of thumb in water service puts the chloride limit at roughly 200 ppm for 304 and roughly 1,000 ppm for 316 at ambient temperature. Outdoors, the same logic explains why 304 develops brown tea staining near the coast or along salted roads while 316 stays bright longer.
Neither grade is immune to chloride stress corrosion cracking. Above about 140°F (60°C), chlorides combined with tensile stress can crack both, and warm, concentrated chloride service generally needs a different alloy family altogether.
What PREN tells you
The pitting resistance equivalent number ranks stainless grades by their alloy content: PREN = %Cr + 3.3 x %Mo + 16 x %N. With no specified molybdenum, typical 304 lands at about 18 to 20, while typical 316 reaches about 23 to 25. A higher number means better resistance to pitting and crevice corrosion. PREN is a ranking tool, not a service-life prediction: surface finish, crevice design, temperature and cleaning matter as much as the number.
Cost difference between 304 and 316
316 typically costs more than 304 because nickel and molybdenum are expensive alloying elements, and 316 carries more of the first and all of the second. Stainless prices usually include alloy surcharges that move with nickel, chromium and molybdenum markets, so the spread changes over time. Because the premium depends on those surcharges and on product form, compare current quotes for the same size, thickness and finish rather than relying on a fixed percentage.
Fabrication cost is about the same for both grades, so the material premium is the main difference in part price. Weigh it against the cost of failure. Specifying 316 everywhere wastes money on indoor parts, while using 304 at a coastal site can mean staining, pitting and replacement within a few seasons. On mixed assemblies, the two grades can usually be combined without significant galvanic concern, as long as 304 is kept off the surfaces that see the salt.
Is 304 or 316 magnetic?
Both grades are nonmagnetic in the annealed condition because their austenitic structure does not respond to a magnet. Cold work such as bending, forming, drawing or cold rolling can transform some austenite into martensite, which is magnetic, so formed corners and edges may attract a magnet slightly. 304 is more prone to this than 316, because 316’s higher nickel content makes its austenite more stable.
Welds can also show slight magnetism, since weld metal is normally designed to contain a small amount of ferrite to prevent hot cracking. None of this reduces corrosion resistance in a meaningful way. It does mean a magnet cannot tell 304 from 316. Use the mill test report tied to the heat number, a molybdenum spot test, or handheld XRF analysis to confirm the grade.
Fabricating 304 and 316
Shop practice is nearly identical for the two grades. Both cut cleanly on a fiber laser with nitrogen assist, both bend with more springback and higher loads than carbon steel, and both distort more under welding heat because of high thermal expansion and low conductivity. 316 work hardens at a slightly lower rate than 304, but machining practice is the same for both: sharp tools, steady feeds and enough depth of cut to stay under the hardened layer.
The main differences are filler metal and the low-carbon decision. 304 is usually welded with ER308L and 316 with ER316L, so the weld carries the same molybdenum as the base metal. For heavy sections and multi-pass welds, specify the L grade of whichever alloy the environment calls for.
When to use 304 and when to use 316
| Application or environment | Usual grade |
|---|---|
| Indoor equipment, enclosures and frames | 304 |
| Food preparation and commercial kitchens without brines | 304 |
| Potable and low-chloride water | 304 |
| Rural or mild inland outdoor exposure | 304 |
| Coastal sites and salt spray | 316 |
| Marine hardware and shipboard components | 316 or 316L |
| Road salt and deicing chemical exposure | 316 |
| Brines, chloride sanitizers, pharmaceutical processing | 316 or 316L |
| Heavy welded sections in mild service | 304L |
| Heavy welded sections in chloride service | 316L |
If you are unsure, start with the environment: how much chloride the part will see, how warm it runs, whether it has crevices or trapped water, and how often it is cleaned. Then weigh the cost of a corrosion failure against the material premium. For grade details, see the guides to 304 stainless steel, 316 stainless steel and 316L for welded parts.
Buying 304 and 316 stainless from ASA
ASA stocks 304, 304L, 316 and 316L stainless in its sheet and plate line, with mill certifications and full material traceability so the grade you specify can be documented back to the mill heat. ASA can laser cut, form and weld either grade on its 8 kW Trumpf fiber laser, CNC press brakes and robotic weld cells, with most JIT orders delivered in 24 to 48 hours across New England and New York. Request a quote for 304 or 316 stainless and include the environment if you would like help choosing.
Frequently asked questions
Can you tell 304 and 316 apart by looking at them?
No. The two grades look identical in the same finish and both are nonmagnetic when annealed, so neither appearance nor a magnet separates them. Reliable methods are the mill test report tied to the heat number, a molybdenum spot test kit, or handheld X-ray fluorescence analysis, which reads the molybdenum content directly.
Is 316 stronger than 304?
Not meaningfully at room temperature. ASTM A240 sets identical annealed minimums for both grades: 75 ksi (515 MPa) tensile and 30 ksi (205 MPa) yield, with 40% elongation. 316 holds its strength somewhat better at elevated temperatures. For most parts, choose between them on corrosion resistance and cost rather than on strength.
Can 304 and 316 stainless be used together?
Yes. They can generally be welded or fastened together without significant galvanic corrosion, since both are austenitic stainless steels with similar electrochemical behavior. The assembly is only as resistant as its weaker part, though, so 304 components in a 316 assembly will be the first to stain or pit under salt exposure.
Is 316 worth the extra cost?
It is worth it wherever chlorides are present: coastal sites, marine hardware, road salt, brines and chloride-based cleaners. In those settings 304 can pit or stain quickly, and replacement costs far more than the material premium. For dry indoor equipment and most food or freshwater service, 304 performs well and saves money.
What is the difference between 304L and 316L?
The same molybdenum difference that separates 304 and 316 separates their low-carbon versions. 304L and 316L both limit carbon to 0.030% so welds resist intergranular corrosion, but 316L adds 2 to 3% molybdenum for chloride resistance. Pick 304L for welded parts in mild environments and 316L for welded parts exposed to salt.