Steel Fabrication for Robotics and Automation Equipment

The fabricated steel behind robotic cells and automated machines: pedestals, frames, guarding and covers, plus the stiffness, flatness and safety details that make them work.

Updated October 2026 5 min read By the ASA team

On this page
  1. Fabricated parts in a robotic cell
  2. Robot pedestals and risers
  3. Machine frames and bases
  4. Safety guarding and fencing
  5. Covers, panels and control enclosures
  6. Steel, stainless or aluminum
  7. Automation fabrication at ASA

Robots and automated machines run on fabricated metal. Every cell needs a pedestal or riser for the robot, a frame or base for the tooling, fencing and guards around the hazard zone, and sheet metal covers, panels and enclosures for controls. Steel fabrication for robotics is about building those parts stiff, flat and repeatable, so the robot hits the same point every cycle and the cell can be copied from one line to the next.

System integrators and automation OEMs typically design the cell and source these parts from a fabricator who can cut, form, weld, machine and finish them to print, often in small batches of near identical cells.

Fabricated parts in a robotic cell

ComponentWhat it doesTypical construction
Robot pedestal or riserRaises the robot and anchors it to the floorHeavy tube or plate column, thick top and base plates, gussets
Machine frame or tableCarries fixtures, conveyors and process equipmentWelded tube or structural frame with machined mounting surfaces
Gantry and linear axis framesSupport overhead or linear robot axesStructural or tube weldments with machined rail seats
Safety fencing and guardsKeep people out of the hazard zoneTube or formed posts, mesh or solid panels, interlocked doors
Covers, panels and enclosuresHouse controls and close off moving partsLaser cut and formed sheet, powder coated
Brackets and mountsHold sensors, cameras, cable carriers and valvesLaser cut plate and formed sheet

Robot pedestals and risers

A pedestal has one job: hold the robot base still. Any deflection or vibration at the mounting surface shows up as error at the tool, amplified by the length of the arm. Robot manufacturers publish the maximum forces and moments their robots apply to the base, including during an emergency stop, and the pedestal is designed to carry those loads with very little movement.

  • Stiff sections. Large square or rectangular tube, or a plate box section, resists bending and twisting better than an open shape of the same weight.
  • Thick plates. The top plate carries the robot’s bolt pattern and is usually machined flat after welding. The base plate carries the anchor pattern and is often thicker than it looks necessary, because anchor loads during a hard stop are high.
  • Gussets. Gussets between column and plates stiffen the joints where most deflection starts.
  • Leveling and grout. Leveling screws and a grout pad under the base plate give full contact with the floor.

Tip: Ask the robot integrator for the robot model’s published base loads and mounting surface requirements, and put them on the pedestal drawing. They tell the fabricator which surfaces must be machined and how flat they need to be.

Machine frames and bases

Automation frames are usually welded from structural tube because it is stiff in every direction, easy to fit square and clean looking once coated. A few practices make a big difference:

Tab and slot construction

Tube and flat lasers can cut tabs, slots and notches that lock members together in the right position. Parts drop into position on the weld table, which cuts fit-up time and keeps every frame in a batch the same. Our guide to tube laser cutting shows the features that are possible.

Machined mounting surfaces

Linear rails, fixture plates and conveyor mounts need flat, coplanar surfaces that welding alone cannot produce. Weld mounting pads to the frame with machining stock, then machine them in one setup after welding, and stress relieve first if the frame is large or heavily welded. The same approach applies to the heavy bases covered in heavy-duty steel frames and weldments.

Repeatability across cells

Integrators often build the same cell many times. Fixtures, locked CNC programs and robotic welding of the frames keep cell number twenty the same as cell number one, so tooling and robot programs transfer without rework.

Safety guarding and fencing

Industrial robots and robot systems are covered by ISO 10218, adopted in the US as ANSI R15.06 (published by A3, formerly RIA). It requires the hazard zone to be safeguarded, most often by keeping people out while the robot runs. Guard design also draws on ISO 14120 for fixed and movable guards and ISO 13857 for safety distances, which relate the size of openings in a guard to how far it must stand from the hazard.

  • Posts are usually square tube or formed sections with welded base plates, laser cut for panel brackets.
  • Panels are welded wire mesh, perforated or expanded sheet in a formed frame, or solid sheet or polycarbonate where welding flash, chips or fluids must be contained.
  • Doors carry interlock switches and must align accurately with them, so hinge and switch mounting holes are best laser cut rather than drilled on site.
  • Color is often safety yellow for guards, with the colors themselves defined by ANSI Z535.1.

The integrator’s risk assessment sets guard height, opening size and distances. The fabricator’s role is to hold those dimensions exactly, because a larger mesh opening or a lower panel can change whether the guard meets the safety distance requirement.

Covers, panels and control enclosures

Automated machines carry a surprising amount of sheet metal: covers over drives and conveyors, panels that close off the machine base, operator stations, cable trays and electrical enclosures for the controls. These parts are laser cut and press brake formed, then powder coated to match the machine.

Two details save time at assembly. First, cut every mounting hole, cable cutout and fastener location in the flat blank, so nothing is drilled by hand on the build floor. Second, design removable covers with captive or self-clinching hardware, since maintenance staff will remove them many times over the life of the machine. Enclosures that must meet a NEMA type are covered in our guide to custom steel enclosures.

Steel, stainless or aluminum

Material choice for automation equipment comes down to stiffness, weight, environment and cost.

MaterialStrengthsCommon uses
Carbon steelHighest stiffness for the cost, easy to weld, stiffness and mass keep vibration lowPedestals, frames, bases, guard posts
Stainless steel 304 or 316Corrosion resistance and cleanabilityFood, beverage, pharmaceutical and washdown automation
AluminumLight weight, corrosion resistance, easy to cutMoving structures, covers, panels, mobile robot bodies

Stiffness is where the two metals differ most. Aluminum’s modulus of elasticity, roughly 10,000 ksi (69 GPa), is about one third of steel’s 29,000 ksi (200 GPa), so an aluminum pedestal or base would need a much larger section to deflect as little as a steel one. That is why fixed structures such as pedestals and bases are almost always steel, while parts that move or must be carried are often aluminum. See aluminum vs steel for a fuller comparison.

Automation fabrication at ASA

American Steel & Aluminum fabricates pedestals, frames, guarding and sheet metal parts to integrators’ and OEMs’ drawings, using a Trumpf 5-axis tube laser for tube up to 6.00 in OD, an 8 kW fiber laser for sheet, CNC press brakes, robotic weld cells, machining and powder coating. Carbon steel, stainless and aluminum come from ASA’s own stock, with mill certifications and full material traceability available. Learn more about industrial equipment manufacturing or call 1-800-933-7833.

Frequently asked questions

How stiff does a robot pedestal need to be?

Stiff enough that the forces and moments the robot applies, including during an emergency stop, cause only negligible movement at the mounting surface. Robot manufacturers publish these base loads for each model. The pedestal designer uses them to size the column, plates, gussets and anchors, and often checks the natural frequency so the pedestal does not resonate with robot motion.

What safety standards apply to robot cell guarding?

Industrial robot systems are covered by ISO 10218, adopted in the US as ANSI R15.06, now published by A3. Guard construction draws on ISO 14120 for fixed and movable guards and ISO 13857 for safety distances, while interlocking doors follow ISO 14119. The integrator's risk assessment determines which requirements apply and sets the guard heights and distances for the cell.

Why are automation frames usually made from square tube?

Square and rectangular tube is stiff in bending in both directions and resists twisting far better than open shapes like channel or angle. It welds cleanly at corners, gives flat faces for mounting components and looks finished once powder coated. Tube lasers can also cut tab and slot joints that make frames quick and accurate to fit.

Should robot pedestal top plates be machined?

Usually, yes. Welding the column and gussets distorts the top plate, and most robot manufacturers specify how flat the mounting surface must be. Machining the top plate after welding, with the bolt pattern cut in the same setup, gives a flat surface and accurate hole locations. Leave machining stock on the plate so it cleans up fully.

Can aluminum be used for robot cell structures?

Aluminum works well for parts that move or must be light, such as end effector frames, mobile robot bodies, covers and some guard panels. For fixed structures like pedestals and machine bases, steel is usually preferred because it is about three times as stiff, costs less and its extra mass helps keep vibration from robot motion low.

Material, processing and fabrication from one supplier

Send a drawing or a material list and the ASA team will quote it from stock.