On this page
Stadium and arena seating is carried by sloped steel raker beams that step up row by row, supporting precast concrete or steel risers on which the seats are mounted. Around that structure sit stair stringers, guardrails, handrails, vomitory framing and walkway platforms, almost all of them fabricated from structural shapes, tube and plate.
Seating steel is repetitive but rarely identical. Sightlines change riser heights from front to back, crowds load the structure dynamically, and much of the steel is exposed to weather or the public eye, so fabrication accuracy and finish matter as much as strength.
Types of seating structures
| System | Structure | Typical use |
|---|---|---|
| Seating bowl on rakers | Steel or concrete raker beams supporting precast or steel risers | Stadiums, arenas, large venues |
| Steel grandstand | Elevated steel frame with aluminum or steel seat and foot planks | School and college fields, racetracks, outdoor venues |
| Telescopic seating | Retractable rows on a manufactured steel understructure | Gymnasiums, multipurpose arenas |
| Portable and demountable stands | Bolted modular steel or aluminum frames | Events, temporary venues, sports facilities |
Telescopic and many portable systems are proprietary products designed by their manufacturers. Seating bowls and custom grandstands are designed by the project’s structural engineer and built from fabricated steel.
Codes and loads that drive the steel
- ICC 300. The Standard for Bleachers, Folding and Telescopic Seating, and Grandstands, referenced by the International Building Code, covers design, construction, egress geometry and inspection of these structures.
- Live load. ASCE 7 specifies a uniform live load of 100 psf (4.79 kN/m²) for bleachers and grandstands, and 60 psf (2.87 kN/m²) for stadium and arena areas with fixed seats fastened to the floor.
- Sway load. ASCE 7 and ICC 300 also require seating to be designed for horizontal swaying forces from the crowd: 24 lb per linear foot (350 N/m) of seat parallel to the rows and 10 lb per linear foot (146 N/m) perpendicular to them, applied separately.
- Guards and handrails. ASCE 7 requires handrail and guard systems to resist a uniform load of 50 lb per linear foot (0.73 kN/m) applied in any direction along the top rail and, separately, a 200 lb (0.89 kN) concentrated load applied in any direction at any point.
- Vibration. Crowds jumping or stamping in rhythm can excite a seating structure. AISC Design Guide 11 gives criteria for rhythmic activity, and the engineer may stiffen rakers or adjust spans to keep natural frequencies out of the range people can drive.
The structural engineer sets the member sizes, connections and welds to meet these requirements. The fabricator builds to the approved shop drawings, and changes to member size or weld detail go back to the engineer.
Steel components in a seating structure
| Component | Typical material | Key processing |
|---|---|---|
| Raker beams | W-shapes or built-up plate girders | Sawing, coping, welded stepped seat brackets, end connections |
| Riser supports and steel risers | Angles, channels, bent plate | Cutting, forming, punching for anchors and seat mounts |
| Columns and bracing | W-shapes, HSS, angles | Base plates, gussets, slotted brace ends |
| Stair stringers and landings | Channels, plate, tread plate | Coping, tread clip layout, welding |
| Guardrails and handrails | Structural tube and bar | Miter cutting, bending, welding, grinding |
| Walkways and platforms | Diamond plate, tread plate, framing angles | Plate cutting, forming, welding |
Fabrication details that matter
Stepped raker geometry
Seating bowls are laid out for sightlines, so riser heights usually grow toward the back of each tier. That means the step brackets on each raker sit at different heights and spacings, and rakers in curved or corner sections differ from each other as well. Laying out brackets from a common datum at one end of the beam, with locations taken from the detailing model, prevents small errors from adding up along a long raker.
Repetition with variation
A bowl can contain hundreds of rakers, risers and rail sections that look alike but are not interchangeable. Clear piece marks, sequence bundling and delivery in erection order keep the site from sorting steel by hand. Kitting rail posts, brackets and hardware by section helps installers.
Corrosion protection
Outdoor stadiums expose steel to rain, snow and deicing salts, and food and beverage spills reach steel in every venue. Exposed steel is commonly hot dip galvanized to ASTM A123, often with a paint topcoat for color. Tube and enclosed members need vent and drain holes, placed as ASTM A385 describes, so zinc can flow in and out safely. See powder coating vs paint vs galvanizing for how the finishes compare.
Weld quality
Because seating sees repeated dynamic loading, the engineer may specify weld profiles, sizes and inspection requirements beyond the minimums. Welds on exposed rails and brackets are often ground smooth for appearance and to remove snag points.
Tip: Show vent and drain hole locations on the shop drawings for any member that will be galvanized. Holes added later by the galvanizer may land where they are visible or weaken a connection.
Railings, stairs and walkways
Railings are the most visible steel in a venue and the part spectators touch. Under the 2010 ADA Standards, circular handrails must have an outside diameter of 1-1/4 to 2 in (32 to 51 mm) and a top surface 34 to 38 in (865 to 965 mm) above the stair nosing or walking surface. Guard heights and the rails in front of seating rows follow the building code and ICC 300.
Aisle stairs in a seating bowl have their own geometry, with treads that match the row spacing and risers that change with the bowl, so stringers and rails are usually fabricated to field verified dimensions. Walkway and platform surfaces often use tread plate or diamond plate for slip resistance.
Planning a seating steel order
- Lock the bowl geometry first. Row spacing, riser heights and sightline layout drive every raker bracket. Changes after release ripple through dozens of members.
- Separate the visible steel. Rails, fascia and exposed brackets may need a higher appearance standard than hidden framing. Mark them on the drawings so finish and grinding expectations are clear.
- Decide the coating early. Galvanizing affects vent holes, bolt hole sizes for coating build-up and how long members can be, since they must fit the galvanizing kettle.
- Match delivery to erection. Ship rakers, risers and rails by section and sequence, and hold rails until the precast or steel risers they attach to are in place.
- Plan for the season. Venue work is often scheduled around event calendars, so confirm material availability before committing to a construction window.
Seating steel from ASA
American Steel & Aluminum supplies structural shapes, structural tube, plate and diamond and tread plate for seating structures, and processes them to the fabricator’s or contractor’s drawings with sawing, miter cutting, beam drilling and coping, plasma and oxy-fuel plate cutting, forming and welding. Mill certifications and full material traceability are available, and ASA’s own trucks deliver across New England and New York. See our steel processing capabilities or request a quote.
Frequently asked questions
What is a raker beam?
A raker beam is a sloped structural member that follows the incline of a seating bowl. It carries the risers and seats and transfers their load to columns and foundations. Rakers are usually steel W-shapes or built-up plate girders with stepped brackets welded along the top, or precast concrete members, and they set the row spacing and riser heights of the seating above.
What live load are bleachers designed for?
ASCE 7 sets a uniform live load of 100 psf for bleachers and grandstands, and 60 psf for stadium and arena areas with fixed seats fastened to the floor. Seating structures must also resist horizontal sway forces applied along and across each row of seats. ICC 300 adds requirements specific to bleachers, folding and telescopic seating and grandstands.
Why does crowd vibration matter for stadium steel?
Spectators jumping or stamping together apply rhythmic loads that can match the natural frequency of a seating structure, causing motion that feels unsafe even when stresses are low. Engineers check this using guidance such as AISC Design Guide 11 and may stiffen rakers, shorten spans or add bracing so the structure's natural frequency stays above the range a crowd can excite.
Should outdoor grandstand steel be galvanized or painted?
Hot dip galvanizing is the most common choice for outdoor grandstand and stadium steel because zinc protects inside and outside surfaces, edges and corners, and needs little maintenance. Where color matters, a paint topcoat over galvanizing, called a duplex system, combines the two. Painted steel alone needs more frequent maintenance in wet or salted environments.
Are aluminum bleachers better than steel?
Aluminum seat and foot planks are light, resist corrosion without coating and stay cooler to the touch than dark painted steel, which is why they are common on grandstands and bleachers. The understructure is often steel because it is stiffer and less costly for the same load. Many systems combine aluminum planks on galvanized steel frames.