Steel Service Center in Portland, Maine

ASA's South Portland service center stocks carbon steel, stainless and aluminum, saws and processes it to size, and delivers it across Maine on ASA trucks.

ASA Portland 115 Wallace Avenue, South Portland, ME 04106

On this page
  1. Metals stocked for Maine customers
  2. Leveled and cut-to-length sheet through ASA
  3. Sawing and shearing to size
  4. Kanban and VMI for Maine manufacturers
  5. Buying metal from ASA South Portland

ASA’s South Portland facility is Maine’s only full-service metals distributor, according to ASA: a combined 120,000 sq ft service center that stocks carbon steel, stainless steel and aluminum, processes it to size and trucks it to customers throughout Maine on ASA’s own fleet. ASA has supplied Maine customers for more than four decades.

For manufacturers, fabricators and contractors in Maine, that means metal can be bought cut to size close to home instead of arriving in mill sizes from out of state. This page covers what the service center stocks and how material can be processed before it ships.

Metals stocked for Maine customers

South Portland customers order from ASA’s stock list. The table pairs each product family with the kind of work it typically goes into.

Product familyExamples on the stock listTypical uses
Carbon steel sheet and plateHot rolled and cold rolled, A36, HSLA, C1008, C1010Brackets, frames, machine bases, general fabrication
Stainless steel304, 304L, 316, 316L, 430Washdown equipment, marine hardware, architectural trim
Aluminum3003-H14, 5005, 5052-H32 and H34Marine parts, enclosures, panels
Coated steelGalvanized, galvannealed, Galvalume, aluminizedOutdoor enclosures, ductwork, painted parts
Floor plateTread bright and diamond plateSteps, platforms, truck and trailer floors
Shapes, bar and tubeAngle, channel, wide flange beam, flats, rounds, tubeFraming, supports, machined parts

Coastal and marine work, common across Maine, often points toward 316 stainless or 5052 aluminum because both resist salt exposure better than their general-purpose counterparts. Galvanized and other coated sheets cover outdoor parts where bare carbon steel would rust and stainless would be more than the job needs.

For the differences between raised pattern floor plates, see tread plate vs diamond plate.

Leveled and cut-to-length sheet through ASA

Metal that comes off a coil carries coil set, a curve left from being wound, and can show crossbow or edge wave. South Portland customers can order sheet flattened and cut to length on ASA’s Alcos 6-high leveling line, and the quote confirms which ASA location processes the order. In a 6-high leveler, small work rolls bend the strip back and forth while intermediate and backup rolls keep those work rolls from deflecting, which lets the line flatten material evenly across its width.

Alcos line parameterRange
Aluminum thickness0.032 to 0.125 in (0.81 to 3.18 mm)
Stainless thickness24 to 10 ga
Carbon and coated steel thickness24 to 11 ga
Width14 to 72 in (356 to 1,829 mm)
Length28 to 190 in (711 to 4,826 mm)

PVC film and interleaving can be applied to protect finished surfaces, which matters for stainless and aluminum that will be visible in the final product. Sheets cut to the exact length you use avoid trimming and drop at your shop. Flat sheet also behaves better downstream: it sits evenly on a laser or punch table, feeds cleanly into a press brake and fits fixtures without being forced into position. Details are on the leveling and cut-to-length page.

Sawing and shearing to size

Long products need different cutting. Saw cutting is part of the South Portland operation alongside angle processing, and ASA’s saw fleet covers bar, tube and shapes up to 25 in square, with bevels up to 45 degrees, so frame members can arrive cut to length and angle. For sheet, ASA’s shearing makes fast straight cuts, which is often the most economical way to produce rectangular blanks. The guide to metal shearing explains when shearing beats other cutting methods.

Kanban and VMI for Maine manufacturers

For material used on a steady cycle, South Portland runs kanban and vendor managed inventory (VMI) programs. In a kanban setup, an empty bin or card at your plant signals the next delivery. Under VMI, ASA watches your stock and replenishes it based on usage. Both reduce the time your staff spends ordering and the amount of metal you keep on hand.

A simple two-bin loop shows how it works. Material is used from the first bin while the second stays full; when the first empties, its card goes back to ASA and a refill ships while you draw from the second. Quantities are sized to your usage and the delivery cycle, so neither bin runs dry.

Deliveries run on ASA’s company-owned truck fleet. With just-in-time delivery, most orders are delivered in 24 to 48 hours.

Buying metal from ASA South Portland

South Portland holds one of ASA’s ISO 9001:2015 certificates, and mill certifications and full material traceability are available with orders. Browse ASA’s product line, then send grades, sizes, quantities and processing needs through the request a quote form or call 1-800-933-7833.

Frequently asked questions

What does ASA's South Portland service center do?

The South Portland facility stocks and processes carbon steel, stainless steel and aluminum for customers across Maine. Work at the site includes saw cutting, angle processing, tube and flat laser cutting, kitting, kanban and vendor managed inventory, and customers can also order material leveled, cut to length or sheared through ASA. ASA describes it as Maine's only full-service metals distributor.

Can I order leveled, cut-to-length sheet through South Portland?

Yes. ASA's Alcos 6-high leveling line flattens and cuts aluminum from 0.032 to 0.125 in, stainless from 24 to 10 ga, and carbon and coated steel from 24 to 11 ga, in widths of 14 to 72 in and lengths of 28 to 190 in. PVC film or interleaving can be added to protect visible surfaces, and the quote confirms which location runs the order.

How do I get a quote from the South Portland service center?

Use ASA's request a quote form or call 1-800-933-7833. For each item, give the material, grade and specification, thickness or gauge, width, length and quantity, plus any leveling, cut-to-length, sawing or surface protection you need. Mention delivery timing and whether the material repeats, since steady usage can qualify for a kanban or VMI program.

Does ASA deliver metal across Maine from South Portland?

Yes. ASA delivers on its own truck fleet, which serves Maine and the rest of New England as well as New York. Through just-in-time delivery programs, most orders are delivered in 24 to 48 hours, and repeat material can be scheduled or triggered by kanban signals so it arrives before you run short.

Material, processing and fabrication from one supplier

Send a drawing or a material list and the ASA team will quote it from stock.